Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Elmhurst?
Chimney cap and crown work in Elmhurst typically runs $340 to $1,850 depending on what needs doing. A single stainless cap on an existing flue usually lands between $340 and $620 installed, while rebuilding a cracked crown with proper pitch and overhang runs $780 to $1,850. Most homes we see fall in the middle of that spread: a new cap plus crown repair on a two-flue brick chimney, quoted at $900 to $1,300.
Those numbers hold for the housing stock around here. Elmhurst is dominated by brick apartment buildings and attached row houses, many built in the 1920s and 1930s during the neighborhood’s first big building wave, plus a broad band of postwar two-family homes. That mix matters. Brick chimneys from the 1920s have usually had their original mortar crown patched at least once, and a crown that was patched rather than rebuilt tends to fail again within a season or two.
At Elmhurst Chimney Sweep, we handle cap and crown work as a chimney-only trade, using components from Gelco, Famco and Olympia Chimney. Our technicians have up to 9 years of experience. We answer 24/7, and fast dispatch from 7am to 7pm gets an estimator out to look at the top of your chimney before anything is quoted in writing. Estimates are free.
Key Takeaways
- A typical cap-only job in Elmhurst runs $340 to $620 installed.
- Crown repair without a full rebuild runs $520 to $780; a full crown rebuild runs $780 to $1,850.
- Doing cap and crown together saves roughly $150 to $250 compared with booking them as two separate visits.
- A failed crown lets meltwater into the brick, and freeze-thaw damage in this climate turns small cracks into spalled brickwork fast.
- Every job is priced by written estimate, and the estimate is free.
Chimney Cap & Crown Cost Breakdown (2026)
Here’s how the line items break down for a typical Elmhurst chimney. These are typical installed ranges, not bare-material prices, and they include labor, sealant, and disposal of old components where relevant.
| Line Item | Typical Installed Range | What It Covers |
|---|---|---|
| Single-flue stainless cap | $340 – $620 | One cap sized to the flue, screened, with a mounting frame |
| Multi-flue cap (two or more flues) | $520 – $980 | Larger footprint cap spanning several flues on one chimney |
| Custom or oversized cap | $780 – $1,400 | Non-standard footprint, unusual chimney shape, or heavy-gauge build |
| Crown patch (hairline cracks, minor spalling) | $520 – $780 | Cleaning, cutting back loose material, and sealing the crown surface |
| Full crown rebuild | $780 – $1,850 | Removing the old crown, forming a new one with proper slope and overhang |
| Crown with flue tile work | $1,300 – $2,400 | Crown rebuild plus resetting or replacing the top flue tiles |
| Cap and crown together | $900 – $1,300 | Most common combined job on a two-flue brick chimney |
The single biggest driver is access and height. A chimney on a one-story roofline is a very different job from one at the top of a three-story brick building, and Elmhurst has plenty of both. The second driver is condition: a crown with a hairline crack costs far less to address than a crown that has already separated from the flue tiles and is letting water behind it. Material choice moves the number too. Standard galvanized caps sit at the low end and last a shorter time in a climate with real winters; stainless and copper options cost more up front but hold up far better.
One thing worth understanding about cost: a crown isn’t decorative. It’s the sloped concrete or mortar cap that sheds water away from the flue and the brick below. When it’s shaped correctly, with a slope away from the tiles and an overhang past the brick, water leaves the chimney. When it’s flat, cracked, or undercut, water goes into the masonry instead. That’s why we quote crown work by what the crown has to do, not by square footage alone.
What Affects Chimney Cap & Crown Pricing in Elmhurst
- Chimney height and roofline access. Elmhurst’s brick apartment houses and three-story row houses put the chimney crown much further from the ground than a typical suburban ranch. Access time directly affects labor, and a chimney that requires staging or a longer ladder setup costs more than one reached from a standard roof edge.
- Brick age and mortar condition. A lot of Elmhurst brickwork dates to the 1920s and 1930s. When the mortar joints just below the crown have gone soft, a new crown won’t bond properly without repointing that section first. We check this before quoting, because a crown that’s rebuilt over failing mortar is money spent twice.
- Number of flues. A two-family home usually has two flues. More flues mean a wider cap, a longer crown, and more material. The jump from one flue to two is a real cost step, not a rounding error.
- Freeze-thaw exposure. This part of Queens gets cold enough in winter that water trapped in a cracked crown expands overnight and widens the crack. That’s why crown repairs here are treated as urgent rather than optional – a hairline crack in November is a spalled crown edge by February.
- Cap material. Galvanized, stainless, and copper all perform differently. Stainless and copper hold up far longer against winter moisture and summer heat cycling, and the price reflects that.
- Whether the flue tiles are sound. If the top flue tile is cracked or loose, the crown can’t be finished properly until that’s addressed. That’s an add-on, but skipping it means the crown fails again.
How to Save on Chimney Cap & Crown
The most reliable way to keep the number down is timing. A crown addressed while the cracks are still hairline costs a patch. The same crown addressed after two winters of freeze-thaw costs a rebuild, plus repointing, plus possibly flue tile work. In Elmhurst’s climate, waiting is the expensive option.
Book cap and crown together. Both jobs involve getting to the top of the chimney and setting up safely, so combining them avoids paying for access twice. The savings are typically $150 to $250 on a two-flue chimney.
Repair the crown rather than rebuilding it when the damage supports it. A crown with minor surface cracking and sound edges can often be cleaned, cut back, and sealed rather than removed entirely. We tell you which category yours falls into, and we don’t push a rebuild where a patch will genuinely hold.
Ask for a written estimate before any work starts. Our estimates are free, and the written estimate sets the final price – no surprises when the job wraps up. Call (844) 871-3169 to book one. We answer 24/7.
Finally, don’t skip annual inspection. A crown problem caught at inspection costs a patch. A crown problem caught because water has already come through the ceiling costs a patch plus interior repair plus a look at whether the flue liner took on water. The chimney cap & crown service page covers what to expect from a full assessment.
FAQs – Chimney Cap & Crown Cost
How much does a chimney cap cost in Elmhurst?
A chimney cap in Elmhurst typically costs $340 to $620 installed for a single flue, and $520 to $980 for a multi-flue chimney. The lower end is a standard galvanized or stainless single-flue cap; the upper end covers larger footprints and heavier-gauge materials. Custom caps for unusual chimney shapes run higher. Call (844) 871-3169 for an exact quote – estimates are free.
Is it cheaper to repair or replace a chimney crown?
Repair is cheaper when the crown still has sound edges and the damage is surface-level: patching typically runs $520 to $780 versus $780 to $1,850 for a full rebuild. The deciding factor is whether water has gotten behind the crown or the mortar below has gone soft. If the crown has separated from the flue tiles or the brickwork underneath has failed, a patch won’t hold and a rebuild is the honest answer. Call (844) 871-3169 and we’ll tell you which category yours falls into.
Can you install a chimney cap and repair the crown in the same visit?
Yes, in most cases. Cap and crown work on the same chimney is usually completed in a single visit, priced at $900 to $1,300 for a typical two-flue brick chimney in Elmhurst. Combining the two avoids paying twice for rooftop access. Some crown rebuilds need a return visit for the mortar to cure before the cap goes on; we’ll tell you which applies to your chimney in the written estimate. Call (844) 871-3169 to schedule.
How much does crown repair cost if the flue tiles are also damaged?
Crown work combined with flue tile repair runs $1,300 to $2,400 in Elmhurst. Resetting or replacing the top flue tiles adds $500 to $600 over the crown cost, because the crown can’t be formed correctly around a cracked or loose tile. This is common on older brick chimneys in the neighborhood. Call (844) 871-3169 for a free estimate on your specific chimney.
Can you come today to look at my crown?
Same-day scheduling is often available. Estimates are free and we can typically get an estimator out to assess cap and crown needs, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (844) 871-3169. We answer 24/7, and a call outside dispatch hours is booked into the next opening.
Why Choose a Chimney Specialist for Cap and Crown Work
Cap and crown work sits at the top of the chimney, but it depends on everything below it. A crown that’s rebuilt without checking the flue tiles is a crown that will crack again. A cap sized wrong for the flue opening lets water and animals in rather than keeping them out. Both require someone who works on chimneys as the whole trade, not as an add-on to a general handyman’s list.
We’re a chimney and fireplace specialist. Our five services are chimney sweeping, cap and crown work, chimney repair, chimney inspection, and fireplace repair, and nothing outside that scope. When an inspection turns up a compromised flue interior, we can address it with HeatShield ceramic resurfacing, a repair-tier capability that most sweep-only companies don’t offer. When a full reline is the honest answer, we install DuraFlex liner systems. We work with a set of professional-grade suppliers: DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. The cap and crown components we install come from Gelco, Famco, and Olympia Chimney – brands built specifically for chimney applications.
A clean chimney is a safe chimney, and a capped chimney stays that way. From the crown down to the firebox, we work the full system. We tell you what your chimney actually needs, nothing more and nothing less. Estimates are free.
How to Know If Your Crown Needs Attention
You can look from the ground with binoculars, and that’s all we’d suggest – getting on a roof to inspect a crown up close is work for someone with proper fall protection and roof access. From the ground, here’s what signals a problem:
- Visible cracks in the crown surface, especially ones running from the flue out toward the edge.
- Crumbling or spalling at the crown edge, where material is flaking off.
- Water staining on the chimney brick below the crown, or white mineral deposits on the brick face.
- A missing or damaged cap on top of the flue.
- Water on the damper or in the firebox after rain, which often points to a crown problem rather than a roof leak.
If you’re seeing any of those, it’s worth an inspection. Our technicians have up to 9 years of experience diagnosing exactly this kind of failure, and we’ll tell you whether a patch or a rebuild is the right call. Call (844) 871-3169. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Elmhurst market as of 2026. Elmhurst Chimney Sweep offers free estimates – call (844) 871-3169.
Written by the team at Elmhurst Chimney Sweep.
What Our Customers Say
"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Greg Walsh"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."
- Kelly Rhodes"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."
- Devon Coleman