Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Elmhurst Homeowners
The cap and crown are the two parts of your chimney that take the weather head-on, and in Elmhurst that means humid summers, freeze-and-thaw winters, and heavy rain that finds every cracked joint. A missing or bent cap lets water pour straight down the flue and lets birds, squirrels and raccoons move in. A cracked crown lets water soak into the masonry around the flue, and once that masonry freezes, the spalling begins and the repair grows from a small job to a large one. We install caps and rebuild or coat crowns using Gelco, Famco and Olympia Chimney components, sized to the flue, sealed to the masonry. Our technicians have up to 9 years of experience, and every repair starts with a camera inspection so you see what we see. Call (844) 871-3169 for a free estimate.
What Our Chimney Cap & Crown Service Includes
Caps and crowns work as a system, and we treat them that way. One piece keeps the rain and animals out of the flue opening; the other sheds water across the top of the masonry and away from the mortar joints. When either one fails, the water damage below them follows quickly. Here’s what each part of the job involves.
Cap Installation
A chimney cap is the protective cover that sits over the flue opening, with a mesh screen around the sides for exhaust and a solid top that keeps rain, snow and debris out. You need one if your flue is open to the sky, if birds or squirrels have found their way in, or if you’ve noticed water stains in the firebox after a storm. We measure the flue, set a correctly sized cap from Gelco, Famco or Olympia Chimney on a sealed, fastened mounting, and check that the draft still pulls properly once it’s on.

Cap Replacement
Caps rust, dent, lose their screens and get knocked loose by wind and by the branches that hang over many Elmhurst roofs. A cap that’s tilted or half-detached can do as much damage as no cap at all, because it channels water toward one side of the crown instead of shedding it evenly. We remove the old unit, inspect the flue top for damage the failing cap may have caused, and fit a new cap that’s sized for your flue rather than the generic model that was there before.

Crown Repair
The crown is the concrete or mortar surface at the very top of the chimney, sloped so water runs off toward the edges. Hairline cracks are common and not always urgent; wider cracks, crumbled edges and a crown that’s pulling away from the flue are a different matter, because each one lets water into the masonry below. We rebuild failed crowns with a proper slope and a bond break at the flue so the crown can move without cracking the flue, then seal the new surface once it cures.

Crown Coating
Crown coating is a flexible, waterproof membrane applied over a crown that’s still structurally sound but showing surface cracks and wear. It’s the right call when the crown is intact but porous, and it’s a smaller job than a full rebuild. We clean and prep the surface properly first, because a coating over dirt or loose mortar won’t hold, then apply a coating that moves with the crown through freeze-thaw cycles instead of cracking off it.
Multi-Flue Cap
Homes with more than one flue, whether from a fireplace, a furnace or an older heating system, need a cap that covers the whole top of the chimney rather than a single pipe. A multi-flue cap is one unit with a mesh enclosure around every flue, which keeps animals out of all of them and gives the top of the chimney a cleaner, more finished look. We build these to the exact footprint of your chimney, since a loose-fitting unit rattles in wind and lets water in at the edges.
Custom Cap
Some chimneys don’t fit a stock size: oversize flues, unusual shapes, chimneys with a strong draft that need a taller cap, or a crown that’s already been rebuilt and needs a cap that matches it. A custom cap is fabricated to your chimney’s dimensions so it fits flush, seals correctly and looks intentional from the street. We take the measurements on site and have it built from Gelco, Famco or Olympia Chimney components to match the rest of the job.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We fit caps and crowns from Gelco, Famco and Olympia Chimney, all three made specifically for chimney work rather than adapted from general sheet metal. Gelco and Famco both make caps in a range of sizes and finishes, which matters when your flue isn’t a stock width, and Olympia Chimney components are a good match for multi-flue and custom builds where the fit has to be exact. We also work with DuraFlex liner systems when the inspection shows the flue itself needs attention beneath a new cap, and HeatShield ceramic resurfacing when the interior has cracks that a cap alone won’t fix.
If your chimney already has a cap from one of these makers and it’s rusted, bent or missing its screen, we can tell you whether a replacement part will do or whether the whole unit needs to come off. Whether you have Gelco or any other make, we can help, and we’ll tell you what the chimney actually needs rather than selling the largest job on the list.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If the firebox is damp or the firebrick is stained after a storm, the cap is missing, damaged or the wrong size for the flue. Water inside the firebox leads to rusted dampers and crumbling brick if it’s left through a season.
- Animals or nesting material in the flue. Birds, squirrels and raccoons treat an open flue as a ready-made den, and nesting material blocks the draft and is a fire hazard. A screened cap closes that door permanently.
- Cracks or crumbling at the top of the chimney. A crown with deep cracks, a crumbled edge or a visible gap where it meets the flue is letting water into the masonry. The earlier that’s caught, the smaller the repair.
- Rust streaks or a tilted cap. Rust running down the cap or chimney sides, or a cap that’s visibly leaning or loose, means it’s near the end of its life. A loose cap can also come off in high wind, so it’s worth addressing before the next storm.
- White staining or flaking on the brick below the crown. This is a sign of moisture moving through the masonry, often from a crown that’s no longer shedding water. Left alone, it leads to spalling brick and mortar that needs repointing.
Our Chimney Cap & Crown Process – Step by Step
- 1
Inspection first. We start with a camera inspection of the flue and a close look at the crown, cap and the masonry below, and we show you the photos before we recommend anything. That way you’re deciding on evidence rather than on a description.
- 2
A written estimate. You get a flat-price sweep of the work and the parts, agreed before anything is booked. We list what’s needed now and what can safely wait, so the two don’t get mixed together.
- 3
Prep and protection. On the day, we protect the roof and the area around the chimney, remove the old cap or the failed crown surface, and clean the masonry so the new work bonds properly. Loose mortar and dirt are the main reason crowns fail early, so this step gets real attention.
- 4
The install or repair. New caps are set, sealed and fastened to the flue; crowns are rebuilt with a proper slope and a bond break, or coated if the structure is sound. We use Gelco, Famco and Olympia Chimney components so the fit is right for the flue, not approximated.
- 5
Final check and photo report. We check the draft, confirm the cap is seated squarely, and give you a photo report of the finished work. If the inspection turned up anything in the flue that needs a follow-up, we tell you then, and we don’t schedule it unless you want it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Elmhurst?
A typical chimney cap installation in Elmhurst runs $180 – $420 depending on the flue size and whether the cap is stock or custom. A crown rebuild usually runs $350 – $900 depending on how much of the crown has failed and how far the damage has spread into the masonry. Crown coating on a sound crown sits lower, usually in the $250 – $550 range, and a multi-flue or custom cap runs higher than a single-flue stock cap because it’s built to measure.
What moves the price most: the number of flues, the condition of the masonry under the crown, whether the cap is stock or fabricated, and roof access. Height and pitch make a real difference in labor, and a chimney with a steep roof or a tight roof line below it takes longer to work on safely. The way to avoid overpaying is to ask for the camera evidence behind every recommendation, get the work itemized in writing, and separate what’s needed now from what can wait. A crown with hairline cracks can often be watched for a season; a crown that’s pulling away from the flue cannot.
Our estimates are free, the price is set per job by the written estimate, and the local pro who performs the work is licensed and insured as their state requires. Nothing gets recommended without camera evidence you can see for yourself.
Chimney Cap & Crown Near Elmhurst – Our Service Area
We connect homeowners across Elmhurst and the surrounding neighborhoods with independent local chimney professionals, including Rego Park, Middle Village, Glendale, Kew Gardens, Briarwood, Corona and Jackson Heights. Roof access and the age of the housing stock vary block to block, so the estimate starts with a look at your chimney rather than an assumption from the street. Related work like a chimney cap & crown in Rego Park or a chimney cap & crown in Middle Village follows the same process. For the full range of services, see Elmhurst Chimney Sweep.
Serving Elmhurst, NY – Our Local Coverage Area
We serve Elmhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Elmhurst
A chimney cap is the cover over the top of the flue, usually with a mesh screen and a solid lid, that keeps rain, snow, debris and animals out while letting exhaust escape. The crown is the concrete or mortar surface at the very top of the chimney, sloped so water runs off the masonry instead of soaking into it. Together they protect everything below them, which is why we treat them as one job. Call (844) 871-3169 for a free estimate.
Most cap installations are done in a single visit, usually a couple of hours once the flue is measured and the roof is set up. A full crown rebuild takes longer, often most of a day, because the old crown surface has to come off, the new one needs a proper slope and bond break, and a fresh crown should cure before the final sealing. Crown coating is quicker than a rebuild. The estimate you get before booking tells you what to expect for your chimney.
Cap installation typically runs $180 – $420, crown rebuilds run $350 – $900, and crown coating on a sound crown runs about $250 – $550. Multi-flue and custom caps run higher because they’re built to the exact footprint of the chimney. The written estimate sets the final price, and we tell you plainly which items can safely wait. Call (844) 871-3169 for an exact quote, estimates are free.
Yes, we fit and replace caps from Gelco, Famco and Olympia Chimney, as well as DuraFlex liner systems and HeatShield ceramic resurfacing when the flue beneath the cap needs repair. If your cap is already one of those makes and it’s rusted or loose, we’ll tell you whether a replacement part will do or the whole unit needs to come off. Whether you have Gelco or any other make, we can help. The camera inspection shows you what’s wrong before anything is ordered.
Same-day service is often available, and we’ll book you into the earliest opening when you call. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. We’re closed on Saturday.
We stand behind the work and tell you up front what the estimate covers, but we don’t quote warranty terms we haven’t confirmed, so ask about coverage for your specific job when you call. What we can tell you is that the caps and crowns are set, sealed and fastened correctly and checked before we leave, and the finished work comes with a photo report. If something isn’t right, call us and we’ll look at it.
You don’t need to do much. Clear access to the fireplace and the area near the chimney on the inside of the house helps, and move anything breakable away from the hearth. If you have records of past chimney work, have them handy, and tell us about any leaks, animal sightings or draft problems you’ve noticed. We’ll handle the roof access and the setup.
Schedule Your Chimney Cap & Crown Service in Elmhurst Today
A cap and crown that are doing their job are the cheapest insurance your chimney has. If yours are missing, cracked or past their best, call (844) 871-3169 for a free, no-obligation estimate. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. You’ll get camera evidence, a flat-price estimate agreed before booking, and a straight answer about what can wait.
Written by the team at Elmhurst Chimney Sweep.