Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Elmhurst Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning service in Elmhurst, NY, for homeowners whose flues have a flexible stainless liner already installed. Our technicians work with DuraFlex liner systems during many of their service calls, so we sweep and inspect them on the merits of the actual installation instead of treating the brand name as proof the job was done right. That distinction matters in Elmhurst, where so many chimney problems start with a liner that was sized or wrapped poorly years ago.
To be clear about who we are: Elmhurst Chimney Sweep is an independent service provider. We are not affiliated with, authorized by, or acting as a dealer for DuraFlex. We clean, inspect, repair and install DuraFlex equipment, and we use quality parts that fit it.
Our technicians have up to 9 years of experience, and every visit starts with a real look at your flue. Call (844) 871-3169 to set up a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Elmhurst Chimney Sweep for Your DuraFlex Chimney Cleaning?
DuraFlex is one of the most widely installed stainless liners in Queens, and that volume means we see a lot of them.
Our technicians handle both corrugated and smooth-wall DuraFlex liners, insulated kits for wood fireplace inserts, and rigid sections used in masonry rebuilds. They know how each one wears in this housing stock. A corrugated liner in a two-family house that gets fired up on cold nights and then sits idle through a humid summer tells a very different story than a smooth-wall liner on a regularly used fireplace. We read those signs before we touch a brush.
We source genuine DuraFlex liner components and clamps when the existing system is intact. When those parts are on long lead times, we use quality aftermarket caps, top plates and appliance connectors that fit the same application. What we don’t do is claim to stock parts we don’t have, or tell you a liner is fine when the camera says otherwise. We tell you what your chimney actually needs – nothing more, nothing less.
The warranty picture is straightforward. Sweeping and inspection done correctly don’t void a DuraFlex liner warranty, and we work to keep the installation within the practices the manufacturer expects: no gouged liner walls, no crushed offsets, no connector left hanging loose. We’re not the company that issued the warranty, so we don’t speak for them. We just make sure our work doesn’t create a reason to deny a claim.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Elmhurst
Elmhurst’s chimney market is dominated by early-20th-century brick rowhouses and two-family homes, many built before 1930 and converted from coal to oil and now to gas. Their original flues were often unlined or lined with clay tile that’s undersized for modern appliances. That history is why so much of the real work here isn’t sweeping alone. It’s assessing liner integrity and the drafting problems that come with tightly packed vintage blocks, where a DuraFlex liner went in to solve a problem the original chimney couldn’t. Here’s what we find when those installations start to fail.
- Creosote packed into the corrugated ribs. Corrugated DuraFlex liner walls collect creosote in the ribs faster than smooth-wall liner does. It shows up most on oil-to-wood conversions and on fireplaces that get used a few times a year and then sit. The ribs are the trap: a standard brush passes over them and leaves the glaze behind, so we size rotary brushes to the liner and work the profile properly.
- Damaged or torn insulated wrap. The insulation wrap on DuraFlex kits degrades, or it gets torn during an earlier install when the liner was pulled through a tight chase. Once the wrap is compromised, heat transfers to combustible framing around the flue, and the installation stops passing a Level 2 check. We look for this every time we open a chase or inspect from the top.
- Poorly supported top terminations. When the top of a DuraFlex liner isn’t supported correctly, the liner settles or kinks at an offset. Draft drops, and the sag becomes a soot trap right where you can’t see it. In attached rowhouses with shared stacks, a settled liner on one side can affect draft on the other.
- Liner-to-appliance connector failures. Connectors corrode or pull loose at the damper and smoke chamber. That’s a gap between the appliance and the liner, and creosote-laden flue gases leak past the liner into the chimney cavity or back into the room. A smoky smell with no fire burning usually traces to this or to a creosote build-up the last sweep missed.
- Undersized flues behind draft complaints. In the dense blocks south of Queens Boulevard, the original coal-era flues are frequently too small for a modern furnace, so homeowners get weak draft and call for a sweep. Sweeping a flue that’s undersized for the appliance doesn’t fix the complaint. Only a proper assessment does, and sometimes that means relining rather than cleaning.
Damp winters and humid summers here push spalling along old brick and mortar joints, and the freeze-thaw cycles around 32°F crack clay liners that were already weak. A DuraFlex liner inside that chimney protects the flue, but the chimney around it still ages. That’s why we inspect the whole system, not just the inside of the pipe.
DuraFlex Parts & Our Repair-vs-Replace Approach
The first question we answer on any DuraFlex job is whether the liner can stay. If the liner is intact and only the creosote, the wrap or the connector is the problem, we repair. That means genuine DuraFlex liner components and clamps where the existing system calls for them, and quality aftermarket caps, top plates and appliance connectors when genuine parts are on long lead times. We don’t carry an inventory to sell you from, and we don’t order OEM parts just to mark them up. We source what fits the installation in front of us.
If the liner itself is breached or crushed, we tell you plainly. A failed DuraFlex liner can’t be safely spot-repaired. Patching a breach or ignoring a crush point means flue gases and heat go somewhere they shouldn’t, and that’s not a repair we’ll do. Replacement is the honest answer in those cases, and we’ll show you the camera footage that makes the case.
Camera inspection and a photo report come with the visit, so you can see what we see. Nothing gets recommended that you can’t verify with your own eyes. Call (844) 871-3169 when you’re ready to know where your liner stands.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection: camera down the flue, a look at the top termination, the offset, the insulated wrap where it’s visible, and the appliance connector at the damper and smoke chamber. Every finding gets photographed so you see the liner’s actual condition, not just our description of it.
- 2
Repair or install. Based on what the camera shows, we either sweep and correct what’s wrong (creosote removal with rotary brushes sized for the liner, connector replacement, top support rework) or we install or replace liner components. Insulated kit wraps get verified, not assumed.
- 3
Test. After the work, we check draft and confirm the appliance pulls properly. A smoke test or draft reading tells us the system works, not just that it looks clean.
- 4
Warranty-safe documentation. We leave you with a written record of what was found, what was done and what to watch for. That record is worth keeping. If a DuraFlex warranty question ever comes up, you’ll have the paper trail.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Elmhurst
We service and install DuraFlex flexible stainless steel chimney liner systems, including smooth-wall liner, corrugated flexible liner, insulated liner kits for wood fireplace inserts, and rigid stainless liner sections used in masonry rebuilds. If you already have a DuraFlex liner in your flue, we inspect it, sweep it, and tell you honestly whether it’s holding up. If you’re starting fresh because an old clay liner has failed, we can talk through what a liner installation involves for your chimney and appliance. The three services we emphasize most on DuraFlex systems are Level 2 Inspection, Creosote Removal and an Annual Sweep – because that’s the routine that keeps a liner viable and catches the small problems before they become liner replacements.
We Also Service These Brands
DuraFlex is one focus, not the whole picture. Elmhurst Chimney Sweep works with a curated lineup of professional-grade industry brands, including HeatShield for ceramic flue resurfacing and Gelco for chimney caps and crown components. We also work with Olympia Chimney, Famco and Copperfield. That breadth matters when a single system turns out to need components from more than one maker. You don’t need a second vendor, and we don’t push one brand at you.
FAQs – DuraFlex Chimney Cleaning Service in Elmhurst
No. Elmhurst Chimney Sweep is an independent DuraFlex service provider, not a dealer and not authorized by the manufacturer. We clean, inspect, repair and install DuraFlex liner systems using quality parts that fit them, and we say plainly that we don’t speak for DuraFlex or its warranty.
Yes, with the right brushes and the right technique. Corrugated DuraFlex liner walls collect creosote in the ribs, so we use rotary brushes sized to the liner and work the profile carefully instead of forcing a standard brush through. The old habit of a stiff brush driven hard down a corrugated wall is exactly what causes damage. Call (844) 871-3169 and we’ll assess yours before we sweep it.
If you’ve noticed weak draft, a smoky smell in the room, visible damage at the cap or top plate, or you simply don’t know when the liner was last inspected, a Level 2 inspection is what you want. A basic sweep cleans the flue; a Level 2 looks at the liner, the wrap, the offsets and the connector with a camera. In Elmhurst’s older rowhouses, those are usually the places problems hide. Call (844) 871-3169 to book the inspection.
Most often it traces to creosote build-up in the liner or to a liner-to-appliance connector that’s corroded or pulled loose at the damper or smoke chamber. Flue gases leak past the liner and the smell drifts into the room. A Level 2 inspection with a camera confirms which it is. Call (844) 871-3169 for an exact quote – estimates are free.
Sometimes, but not always. If the damage is a torn insulated wrap, a loose connector or a top termination that settled, those are repairs. If the liner itself is breached or crushed, a safe spot repair doesn’t exist and replacement is the honest answer. We show you the camera footage so you can see which one you’re looking at. Call (844) 871-3169 to find out.
Yes. A properly fitted cap keeps rain, debris and animals out of the liner and protects the top termination from the weather. Elmhurst’s humid summers and freeze-thaw winters are hard on anything exposed above the roofline. A cap from a brand like Gelco or Olympia Chimney, sized to your flue, is a modest addition that extends the life of the whole installation. Call (844) 871-3169 for a free estimate.
We price per job with a written estimate, because a corrugated DuraFlex sweep on a rarely used insert fireplace and a Level 2 inspection on a shared rowhouse stack are not the same piece of work. Your estimate is free and the written estimate sets the final price. Call (844) 871-3169 to get yours.
A standard sweep on an accessible DuraFlex liner is usually a short visit. A Level 2 inspection with camera work, or a job that turns up a torn wrap, a settled top termination or a loose connector, takes longer because we document what we find and correct it properly. We’ll tell you which kind of visit you’re booking when you call.
We service flexible stainless steel liner systems, including smooth-wall liner, corrugated flexible liner, insulated liner kits for wood fireplace inserts, and rigid stainless liner sections. If you’re unsure what’s in your flue, the inspection tells us.
Properly done sweeping and inspection don’t void a DuraFlex liner warranty. Our job is to keep the installation within the practices a manufacturer expects: no gouged liner walls, no crushed offsets, no loose connector left hanging. We aren’t the warranty issuer, so we don’t speak for DuraFlex – we just make sure our work doesn’t create a reason for a claim to be denied.
Book Your DuraFlex Service in Elmhurst, NY
If you have a DuraFlex liner in your Elmhurst chimney and you’re not sure where it stands, we can tell you. We do the Level 2 inspection, the creosote removal and the annual sweep, and we show you the camera evidence for anything we recommend. Call (844) 871-3169 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Elmhurst Chimney Sweep.