Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Elmhurst Homeowners
Most of the chimney repair work we see in Elmhurst starts small: a hairline crack in the crown, one loose brick above the roofline, a rust streak on the damper. Left alone, that damage does not stay small. Water gets behind the masonry, freeze-thaw cycles open the joints wider, and what began as a repointing job turns into a rebuild. Our technicians have up to 9 years of experience reading that damage early. We inspect the full venting system and the firebox together, and we tell you what your chimney actually needs – nothing more, nothing less. Same-day service is often possible in Elmhurst. Call (844) 871-3169 to book a free estimate.
What Our Chimney Repair Service Includes
Repair on a chimney is a single trade, not a patchwork of unrelated jobs. Everything below falls inside our scope, which means you deal with one specialist from the inspection through the fix.
Mortar Repointing
Mortar is the softest part of a chimney, and it wears away first. When the joints between the bricks start crumbling or receding, the brick above has nothing holding it in line. Repointing means grinding out the worn mortar to a proper depth and pressing in fresh material that matches the original in flexibility, so it moves with the brick instead of cracking away from it. We do this work on the stack, the crown edge and the joints around the flashing, and we never smear a thin skin of mortar over the face of good brick to hide a bad joint.

Spalling Brick Repair
Spalling is when the face of a brick pops off, flakes away or turns to powder. It happens when moisture gets inside the brick and expands as it freezes, and it is the clearest sign that water is finding a way in. We replace the failed bricks with matching units and correct the source of the moisture, because a brick swapped out without fixing what soaked it will fail the same way. On older Elmhurst homes, spalling is the most common problem we chase down.

Chimney Waterproofing
A waterproofing treatment is a breathable sealer applied to the masonry that keeps rain out while letting vapor escape from inside. It is the single cheapest way to slow the aging of a chimney, and it makes the most sense right after repointing or brick repair, when the surface is clean and sound. We apply it to the stack and crown when the masonry is ready for it, and we skip it when the brick is still holding too much moisture for a sealant to work.

Flashing Repair
Flashing is the metal that bridges the gap where the chimney meets the roof, and it is where a lot of interior leaks begin. When the flashing pulls away, corrodes or was never stepped into the shingles correctly, water runs down the chimney and shows up as a stain on your ceiling a floor below. We reset or replace the flashing with proper counterflashing and sealant, keeping the repair inside the chimney scope rather than handing it off to a roofer.
Chimney Rebuilding
When the top few courses of a chimney have lost their mortar and the brick is too far gone to repoint, the correct fix is to take the stack down to solid masonry and rebuild it. We rebuild from the roofline up, matching the original brick and setting a new crown on top, and we check the flue interior before the rebuild so the finished stack is sound all the way through. A rebuild is the heaviest repair in our menu, and we only recommend it when repointing genuinely will not hold.
Tuckpointing
Tuckpointing is the finer version of repointing: the mortar joint is cut back and refilled with a finished joint that is slightly raised and neatly struck, so the brickwork reads crisp and even. It suits visible chimneys on the front of a house, and it also does real structural work, sealing the joint against weather and locking the brick in place. We match the mortar color and joint profile to the surrounding masonry so the repair does not stand out.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We repair with an intentional lineup of professional-grade materials, the same products certified chimney specialists rely on nationwide. HeatShield is the ceramic resurfacing system we use to restore a flue interior that is cracked or pitted but still structurally there. It is a repair-tier capability most sweep-only companies do not offer, and it lets us repair a compromised flue instead of jumping straight to a full reline. DuraFlex liner systems come into play when the flue needs full relining, and we install them to restore safe draft and contain fire inside the flue.
For cap and crown work we use Gelco, Famco and Olympia Chimney components built specifically for chimney applications, not repurposed roofing metal. Copperfield is in the lineup for masonry and flashing components. If your chimney was fitted with a HeatShield-resurfaced flue or a DuraFlex liner and it needs attention now, we know where those systems wear. Whether you have Gelco, Olympia Chimney, or any other make, we can help.
Signs You Need Chimney Repair Right Now
- Crumbling mortar in the joints. If you can scrape mortar out with a key, the joints have given up and the brick above is being held by habit. Repointing now is a fraction of the cost of a rebuild later.
- White staining or rust on the masonry. White deposits on the brick face mean moisture is migrating through and leaving minerals behind, and rust streaks point to a metal component breaking down inside. Both send you to the same place: repair water intrusion before it spreads.
- Pieces of brick in the firebox or on the roof. Loose brick above the roofline is a safety issue, because masonry that has lost its mortar can fall. This one does not wait for a convenient weekend.
- Water stains on the ceiling or chimney breast. A stain indoors usually traces back to flashing or crown failure, not to the roof itself. It is worth checking the chimney before anyone cuts into the ceiling.
- A damper that sticks, or a fireplace that smokes into the room. Sticking or warped dampers, cracked firebox mortar and a flue that no longer drafts correctly all point to repair work inside the system. If smoke comes into the room with the flue open, stop using the fireplace until it is checked.
Our Chimney Repair Process – Step by Step
- 1
Inspection first. We look at the chimney from the roof, from the ground and from inside the firebox, and we run a camera down the flue where it helps. Nothing gets recommended until we have seen the problem and can show it to you.
- 2
Plain-language diagnosis. We explain what we found, photograph it, and lay out what can safely wait versus what should not. If the flashing is fine and only one joint needs refilling, that is what we tell you.
- 3
Written estimate. You get a line-by-line estimate before any work starts, with the repair scope agreed in writing. The price is set per job by that written estimate, and it does not change because we found something on the roof that we should have seen at the inspection.
- 4
The repair itself. Repointing, tuckpointing, brick replacement, waterproofing, flashing and crown work all happen in one visit where the scope allows. HeatShield ceramic resurfacing or a DuraFlex reline is scheduled as a separate step because those materials need proper cure time.
- 5
Follow-up check and sweep. Once the repair is done we confirm draft, look at the firebox, and sweep the flue so the finished system is clean as well as sound. A clean chimney is a safe chimney – we make sure you have both.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Elmhurst?
Chimney repair in Elmhurst typically runs $250 to $1,800 depending on the scope, with most masonry repairs landing between $400 and $900. A rebuild at the roofline is the top of the range. These are typical estimates; the written estimate sets the final price.
- Mortar repointing or tuckpointing: $250 – $650 for a chimney stack, depending on how many joints are reworked and how much access the roof allows.
- Spalling brick replacement: $300 – $800, based on how many bricks are swapped and whether matching units are available.
- Flashing repair: $250 – $550, depending on whether the flashing is reset or replaced and whether counterflashing is needed.
- Waterproofing treatment: $200 – $500, priced by the surface area of the stack and crown.
- Chimney rebuild above the roofline: $900 – $1,800, driven by how many courses come down and the crown work on top.
What moves the price is access, height, how much of the masonry comes off, and whether the flue interior needs HeatShield resurfacing or a DuraFlex reline on top of the exterior work. To avoid overpaying, ask for the scope in writing and hold off on anything that is not tied to visible damage. Our free estimate includes the inspection, the camera look at the flue and the written scope, so you have a document to compare against any other quote.
Chimney Repair Near Elmhurst – Our Service Area
Elmhurst sits in the middle of a tight cluster of Queens neighborhoods where we work regularly, including Rego Park, Middle Village, Glendale, Kew Gardens, Briarwood, Fresh Meadows, Corona and Jackson Heights. For most of these, we can arrange an Elmhurst Chimney Sweep visit on a short timeline, and same-day service is often possible in the core Elmhurst area when the repair scope is masonry work. If you are further out, call and we will give you a clear expectation before booking anything.
Serving Elmhurst, NY – Our Local Coverage Area
We serve Elmhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Elmhurst
Chimney repair is the work of restoring the physical structure of the chimney and its firebox, including the masonry, mortar, crown, flashing and flue interior. It covers everything from repointing a cracked joint to rebuilding the top of the stack, and it is separate from a routine sweep, though we often do both in one visit. It is not cosmetic work. Every repair on the exterior protects the flue and firebox below. Call (844) 871-3169 for an exact quote – estimates are free.
Most masonry repairs, like repointing, flashing repair or a small brick replacement, are done in a single visit of a few hours. A larger rebuild above the roofline or a HeatShield resurfacing job can take a full day or more, and we schedule it as a separate appointment so the material has proper cure time. We give you a realistic window with the written estimate rather than a guess on the phone. Call (844) 871-3169 for an exact quote – estimates are free.
Typical chimney repair in Elmhurst runs $250 to $1,800, with most repointing and flashing jobs landing between $400 and $900. The number depends on how much masonry has to come out, roof access, and whether the flue interior needs resurfacing or relining on top. The written estimate sets the final price. Call (844) 871-3169 for an exact quote – estimates are free.
Yes, we service HeatShield-resurfaced flues, DuraFlex liner systems and Olympia Chimney caps and crown components as part of our repair work. We install those systems too, so we know exactly what properly set flashing and a correctly cured HeatShield interior look like, and we know where they wear first. Whether you have those brands or any other make, we can help. Call (844) 871-3169 for an exact quote – estimates are free.
Same-day service is often possible in Elmhurst for masonry and flashing work, subject to the inspection findings and the schedule. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we are closed on Saturday, and a call outside dispatch hours is booked into the next opening. Some repairs, like a full HeatShield resurfacing or a rebuild, are scheduled separately because of cure time. Call (844) 871-3169 for an exact quote – estimates are free.
We stand behind the repair work, and the terms that apply to your job are written into the estimate before you book so there are no surprises later. The local professional who performs the work is licensed and insured as their state requires, and we confirm that before any job is booked. If anything looks off after the repair, call us and we will come back and look at it. Call (844) 871-3169 for an exact quote – estimates are free.
Clear access to the fireplace and hearth, and move anything breakable off the mantel and the floor in front of it. If you can, note when you last had the chimney swept and whether you have seen water stains or smoke coming into the room, because those details help at the inspection. You do not need to move furniture on the roof side; we set up our own access. Call (844) 871-3169 for an exact quote – estimates are free.
Schedule Your Chimney Repair Service in Elmhurst Today
If the mortar is going, the crown is cracked or water is finding its way in, we can look at it and tell you what it actually needs. Our free estimate includes the inspection and the written scope, and nothing gets recommended without evidence you can see for yourself. We answer 24/7, so call (844) 871-3169 and we will book your chimney repair visit today.
Written by the team at Elmhurst Chimney Sweep.